More than just products – comprehensive services for metrology: The portfolio of EP Instruments

  • DAkkS-accredited laboratory*

    The calibration laboratory of our subsidary EP Instruments Messtechnik + Kalibrierung GmbH is accredited according to DIN EN ISO / IEC 17025 for the flow calibration of flowing gases and is considered as the most accurate DAkkS laboratory in gas flow technology.

  • CE certifications

    We support you reliably in the CE testing and certification and perform all required measurements and tests directly at your location. So you can be sure your system complies with EU safety requirements.

  • On-site calibration and adjustment

    We calibrate all measured variables of the test bench directly at your location. In the process, our experienced technicians also check the harmonious interaction of all the sensors so that the whole system is perfectly coordinated.

Calibration, services, training - comprehensive services for your test bench

Our subsidiary company EP Instruments completes the offer of EP Engineering perfectly. Our services in this area include:

  • We offer you calibrations for gas flow measurement of gases (Germany's most accurate DAkkS laboratory*) as well as temperature, humidity and pressure measurements.
  • With numerous practical exercises directly on the measurement instrument, we train you thoroughly in the field of flow measurement technology.
  • Comprehensive services, such as CE certifications, as well as the project design and planning of system solutions in the areas of hardware and software development, process development and design as well as repair services and maintenance.
made We produce and calibrate in Baden-Württemberg

* by DAkkS according to DIN EN ISO / IEC 17025 accredited calibration laboratory. The accreditation is valid only for the scope of accreditation listed in the certificate system D-K-15143-01-00.

  • Calibrations

    Precise calibration of sensors and test benches

  • Engineering:

    Services from project planning to maintenance

  • Training sessions:

    Expand knowledge and skills in flow measurement technology

Calibrations Precise calibration of sensors and test benches

Whether in our laboratory or on site at your company - our calibration service checks both individual measuring elements as well as complete test stands. In the DAkkS laboratory of our subsidiary EP Instruments Messtechnik + Kalibrierung GmbH we calibrate components for which we issue you a DAkkS calibration certificate after calibration. Through our accreditation according to DIN EN ISO / IEC 17025 for measured variables of volume and mass flow of flowing gases, our calibrations are traceable to national standards and norms. During a calibration at your location, we put the complete test bench under the microscope. This offers the advantage that not only one component, but rather the entire system is calibrated and the interaction of all sensors is checked. By the way: We also offer this service for test benches made by other manufacturers.

* by DAkkS according to DIN EN ISO / IEC 17025 accredited calibration laboratory. The accreditation is valid only for the scope of accreditation listed in the certificate system D-K-15143-01-00.

Send a custom request
  • Factory calibration of, for example, a Venturi nozzle in the laboratory

  • DAkkS calibration of, for example, a laminar flow element in the laboratory according to DIN EN ISO / IEC 17025

  • On-site calibration of measured variables directly on the test bench

indicate Do you need accurate information about our calibrations and measurements? Then just download our data sheet with detailed information about this subject.

Engineering: Services from project planning to maintenance

We offer you a comprehensive service portfolio for your metrology: our offer in this area ranges from project planning and design, through commissioning and support for the CE certification to the maintenance of your test bench:

Send a custom request
  • CE consultation and certification of systems and test benches: The CE mark documents the fact that systems and test benches meet the health and safety requirements of the European Union. We support you reliably in your CE certification: We examine under which policy your system falls, carry out the necessary tests and measurements, document this, obtained declarations of conformity and affix the CE mark. For more information on this topic, see our data sheet for CE certification.

  • Project support: We are available to you with our expertise during the project design and planning, the set up and commissioning of your test bench. Whether we are to support you during the entire project or only in certain areas is entirely up to you.

  • Maintenance and repair: Test benches and other metrological systems need regular maintenance and are also rarely repaired. Our service team ensures that your systems are always in good shape and that downtimes in case of failure are as short as possible.

  • Test set-ups: implementation of compact test set-ups already pre-designed by the customer.

indicate Do you need accurate information about our calibrations and measurements? Then just download our data sheet with detailed information about this subject.

Training sessions: Expand knowledge and skills in flow measurement technology

Sound technical expertise is the basis of a company in the field of metrology. Continually developing and strengthening the knowledge and skills in this area are therefore a key success factor. We are happy to support you here with our in-depth technical training sessions. Get an overview of the metrology or in our second course learn about flow measurement and calibration with laminar flow elements or Laval nozzles. The training content is very practical and includes numerous practical exercises on the measuring system. Incidentally: we like to perform our training sessions directly at your company.

Send a custom request
  • Course 1: Fundamentals of flow measurement technology: Physical fundamentals, introduction to flow measurement methods, leak testing, demonstrations and practical exercises

  • Course 2: Fundamentals of flow calibration: differential pressure method, laminar flow elements, critically operated nozzles (Laval nozzles). Demonstrations and practical exercises

indicate Do you need accurate information about our calibrations and measurements? Then just download our data sheet with detailed information about this subject.

The most important data sheets

Here you will find data sheets in PDF format about our services in the area of calibration, engineering and training: